Features
standard system - for typical passenger cars CAN-BUS data readout suitable to the 7-pin plug of the trailer LED/bulb lamps support, PWM control trailer LED/bulb lamps support independent rear fog lights control trailer rear fog lights turning-on audio information socket for tri-colour LED indicator audio information about trailer connecion and disconnection trailer's turn signal lights damage datection and audio notification output for enabling of switching off PDC signalization in car OPTION: additionally variants of stitching off PDC signalling using separatelly PDC-OFF modules trailer socket is factory mounted on cable harness displaying malfunction of trailers turn lights on car dashboard display panel (for selected cars) automatically deactivation rear PDC sensors when trailer is connected (for selected cars) automatically blocking of switching-on rear fog-light when trailer is connected (for selected cars) blocking of car trunk opening by driver using remote switch if trailer is connected (for selected cars)
Add to compare list Add to selected
MP2S-CAN-G7

Main module (MP2S-CAN) - in contrast to others - reads inputs data from CAN-Bus of car - not from wires to lamps.Thanks to this count of needed connections under installation time is much less than in case of "typical" modules. More over - main cable harness is already connected with socket - this also makes an installation process easier and faster.

 

Kit MP2S-CAN-G7 contains 7-pins trailer socket.

NOTE: Please remember, that socket G7 not include circuit for REV light. For example in Poland it can be used only with "lightweight trailer" (gross trailer mass up to 750kg).

 

MP2S-CAN module supports many of car models present on the European market - but must be configured for concrete type/model of car. Factory is prepared to with particular group of cars. Module is equipped with an output for deactivate of parking sensors module (PDC) in car - but for some cars this can be realised "directly".
Note: continuous product improvement and availability of electronic components leads MP2S-CAN unit  can be oferred in a few versions with small changes. However, all module functions depends on a current firmware generation and still the same for each of them. Firmware update can be made by own using Bootloader with payment free software.
 

In special cases (when this is required) is possible to make contact-less data reading from CAN-Bus (without "hard" contact - without "phisically integration" with an installation of car) using optionally module MCB-CLICK-CAN.

 

Kit can be is equipped with (otional) LED-RGY-500 - tri-colour LED indicator which inform about:

  • connecting of the trailer;
  • damaging the directions lights on the trailer;
  • switching-on fog light on the trailer.

 

A compatibility list (list of cars and models supported by MP2S-CAN) is available for download below under the FILES tab.

Here are short movies about operate MP2S-CAN.

Product requires to be installed by specialized workshop - read here.

  • Product's EAN code: 5907662621237
Kit contents
  • Main control unit 1 pc
  • Main cable harness with 7-pin socket 1 pc
  • Signal cables harness (to the CAN-Bus) 1 pc
  • Power cable harness 1 pc
  • Mounting set 1 set
  • Screw set 1 set
  • Connections diagram 1 pc
Module main features
CAN-Bus vehicle data readout
LED lights and single filament bulbs support (car)
LED lights and filament bulbs support(trailer)
Trailer/camper connection detection (bulb lamps)
Trailer/camper connection detection (LED lamps)
Ability to control of park sensors module in car
Trailer turn signal lamps failure detection
Trailer reverse light control
Alerts & Notifications
Trailer connection notification
Trailer turn signal failure
Trailer/caravan fog lights switching on/off notification
Car rear fog-lights control modes
Trailer fog lights control modes
sequence or direct
Trailer fog light sequential(independent) control
Car rear fog lights cut-off
Features of electric cable harness
Mounted socket on the cable harness
Length of power harness
5,0 m
Length of cable harness to the socket
1,7 m
Length of input signals cable harness
(to CAN-Bus) 5,0 m
Technical data
Power supply voltage
10-18 V
Position lights output power, max
(each of sides) 3 x 5 W
Stop lights output power, max
3 x 21 W
Turn signal output power, max
(each of sides) 21+10 W
Fog-light output power, max
21 W
Parking sensors output load capacity, max
0,5 A
Kit equipment
Complete bundle of towbar with installation accessories
Filter by car

Select car type, make and model to find available manuals.

clear form

Manuals
Data sheet
Technical Information
Wiring diagrams (general)
Configuration software & Drivers
Firmware